LED Can Light Retrofit for 6

LED can light bulbs

Recessed Lighting FAQ

Q: what exactly is recessed illumination?

A: Recessed lighting describes fixtures that are set into ceilings or wall space. Commonly labeled as cans due to their shape, they include the housing (the inner component when you look at the roof that you do not see) while the trim, which can be noticeable. With little or no profile, recessed lighting provides efficient ambient and accent lighting for both domestic and commercial use.

Q: which kind of housing should I utilize: Remodel or New Construction?

A: There's two types of housings, New Construction and Remodel. Deciding which sort to utilize will depend on your application. For those who have use of your ceiling from preceding, you'll want to make use of a fresh Construction housing. If you don't have admission, you should utilize a Remodel housing.

Q: what's the distinction between IC vs. Non-IC ranked housings?

A: IC rated housings enable insulation (either laid in or blown in) becoming installed on or just around the housing. Non-IC housings need that insulation be held at least 3" from the housing all the time.

Q: How many lights was we have to?

A: This question has no easy solution, as views about this subject vary considerably. But a beneficial principle is use the height of the roof and divide it by 50 percent. This is the distance that each light is from another. Like, a space with an 8' ceiling, must have lights around 4' from one another (8' roof / 2 = 4' apart). The sum total number of lights is likewise affected by the sort and wattage of light bulb being used. Spot lights with narrow beams will create pockets or pools of light, while flooding type bulbs will produce broader quantities of light.

Q: Am I Able To make use of a dimmer?

A: Yes, a dimmer can be utilized of all recessed lighting. Line Voltage recessed lighting could be dimmed with a standard incandescent dimmer. While low-voltage recessed lighting should be dimmed with either a Low Voltage Electronic or Magnetic dimmer. The type of transformer (Electronic or Magnetic) found in the housing should determine which type of dimmer you want.

Q: something meant by Air-Tight down light and just why would i do want to make use of one?

A: Any air-tight ranked down light has actually demonstrated in an unbiased screening laboratory environment that it'll prevent venting through the installation. This is important since it saves profit hvac costs. Just as essential, some state regulations are now actually needing that new house building make use of this kind of down light.

Q: may i utilize a CFL or LED bulb in a Line Voltage Housing and Trim?

A: Yes, CFL and Light-emitting Diode light bulbs can be used in-line Voltage Housings and Trims. These types of bulbs can easily be bought in Par, roentgen and A-shaped light bulbs. You need to note, that the form of the light bulb should really be as near towards bulb specified because of the manufacture as you possibly can. For instance, if the housing and trim are recommending a Par/R shaped bulb, the CFL or Light-emitting Diode light bulb should-be in a Par/R shape. Spiral CFL light bulbs may be used as they have the same socket base as a Par/R bulb, nevertheless due to the length of some light bulbs, the light structure offered off because of the light bulb and overall look, may not be what was originally meant.

Q: Can recessed lights be installed in your bathroom?

A: Yes, recessed lighting trims and housings tend to be suited to wet places (porch or restroom) utilizing any trim. Wet areas, above a shower or out-of-doors, need using specific damp place trims.

Q: The Reason Why Consider Die Cast Trims over Stamped Trims?

A: Aluminum die-cast trims supply more powerful construction, more precise forms and exceptional temperature dissipation properties than corresponding stamped steel choices. Die-cast trims tend to be more powerful due to their single-piece construction versus a stamped trim that is comprised of numerous pieces of metal that are fastened or welded collectively. The die cast procedure creates trims with tighter tolerances than stamping, thus causing higher accuracy of forms with smoother edges. Stamped trims are comparable in appearance to die-cast trims as they make use of the same powder coat finish. In conclusion, die-cast trims look comparable to look at the corresponding stamped trim, but die-cast trims are superior high quality.

Source: www.ylighting.com
LED Bulbs - See what light can do
LED Bulbs - See what light can do
Comparing LED, CFL and Incandescent Light Bulbs
Comparing LED, CFL and Incandescent Light Bulbs
Share this Post

Related posts

LED can light Replacement

LED can light Replacement

APRIL 14, 2024

This item may at this time maintain stock at your local Costco warehouse for immediate acquisition. Our energy saving Efficiency…

Read More
LED PAR light bulbs

LED PAR light bulbs

APRIL 14, 2024

As a result of the insufficient sufficient responses, I made a decision to research the differences myself and provide a…

Read More